Top information

Ground Support Equipment - Know More

PN 3403221-1Description The Cradle Assembly is used with the MWS-16 Maintenance Platform to remove and replace the external fuel tank or inflight refueling pods tanker-version The Cradle Assembly is designed to nest the external fuel tank in nylon webbing and provides some up-down adjustment of the tank for installing wing attach bolts...

Putting a Ball or SAG Mill on Care and Maintenance - Know More

11-09-2015 0183 32 The cradles need to be lifted up to sit under the shell then jacks placed under the cradl You sit the jacks on some big thick steel plate to dissipate the load a bit otherwise could punch through the concrete You will insert the jacks between the cradle and the shell and then if you lift the cradle up off the concrete plinths the same gap...

PRECAST JACKING PIPES TUNNELS SHAFTS - Know More

BENEFITS OF JACKING PIPES Safe - Easi-lift ensures a positive horizontal lift every time, no weight balancing is required Accurate - pipes can be lowered down deep shafts and onto the jacking cradle in one smooth, easy operation Time saving - lifting eyes are engaged and disengaged by rotation in a few seconds...

Jacking Crate System - Know More

29-05-2018 0183 32 Mammoet s jacking crate system safely and swiftly raises or lowers a load into place, replacing the need for manual handling of jacking timbers This hydraul....

SERVICE MANUAL AND INSTRUCTIONS FOR CONTINUED , - Know More

A 3 Revised aircraft jacking position 3/16/2005 B 12,18 Added greasing zerk to tasks and changed drawing 9/28/2005 , FIGURE 31 JACK CRADLE RECOMMENDED MODIFICATION , FIGURE 56 ASSEMBLY NOSE GEAR SYSTEM ....

Join Cell for the G150 Aircraft - Know More

Figure 14 Aft fuselage raft drive assembly isometric view Figure 15 Aft fuselage raft drive assembly plan view Figure 16 Hand crank or drill motor drive for axis of motion There are several mechanical pin-off locations Figures 15, 16, and 17 show two pins for establishing the position of this axis The T-handle clamping pin locks...

METHOD STATEMENT FOR PIPEJACKING - Know More

assembly mounted on the portal structure Additional sections of the TBM will be added as the launch proceeds until the machine is fully assembled The TBM will generally advance in 25m long stag After each stage, the connecting lines will be uncoupled in the pit bottom and a further jacking pipe added, the lines recoupled and excavation ....

Tesla Model 3 Structural Holding System - Know More

JACKING POINT Center Section Jacking Points 1 Locate four 4 Jacking Points on underside of vehicle 2 Place Base Stand at each Jacking Point located in center section of vehicle 3 Confirm Base Stand Assembly is adjusted to 333mm 13-1/8 to maintain a level datum for placing fixtur...

SERVICE MANUAL AND INSTRUCTIONS FOR CONTINUED , - Know More

2 Lower aircraft onto float cradle as shown in Figure 4-4 3 Place fore and aft supports as shown in Figure 4-3 and Figure 4-4 42 LEVELING See applicable aircraft maintenance/service manual 43 JACKING PROCEDURES CAUTION Make sure nothing is under or above the airplane or floats when jacking the aircraft 1 Turn off fuel...

Removing Front Suspension Cradle - Know More

Removing Front Suspension Cradle The Jaguar XJ-S is designed with a front suspension cradle, to which are attached the front hubs and springs It is also responsible for supporting the engine Be forewarned The front suspension cradle is heavy and unwieldy Its removal is not a typical one person operation...

sag mill jacking cradle - Know More

Mill Jacking Cradle In Jacking cradle assembly sag mill jacking cradle cs2be sag mill jacking cradle mine to mill optimisation effect of feed size on mill srk consulting mills and onto the secondary ball mill circuits alleviating a common to the crushinggrinding circuit can achieve up to a 30 mill project must consider both sides how well...

Putting a Ball or SAG Mill on Care and Maintenance - Know More

11-09-2015 0183 32 Jacking/Lifting Cradle The mine is closed and now you need to know how to put the SAG or Large Ball Mill in care and maintenance does not have to be complicated to the point where you need bridge erection equipment for lifting a Mill AG/SAG/Rod/Ball...

Car Lift Accessories - Know More

Frame Cradle Pads 60 mm , Lift Pad Assembly / 60 mm Pin and Polyurethane Tuf-Pad / SET OF 4 , The AK-14 integrated jacking beam airline kit mounts and secures your airline to the bottom of your lift s runways, creating a tidy airline solution for your jacking beams...

Car Hoist Accessories - Know More

Frame Cradle Pads 60 mm , Lift Pad Assembly / 60 mm Pin and Polyurethane Tuf-Pad / SET OF 4 , The AK-14 integrated jacking beam airline kit mounts and secures your airline to the bottom of your hoist s runways, creating a tidy airline solution for your jacking beams...

Heavy lifting Mammoet Cranes Equipment - Know More

Jacking systems are used to elevate large and heavy objects ranging from 6000-ton mining draglines to 23,000-ton offshore decks For instance, Mammoet engineers in the United States perfected a unique new system to jack-up, load and secure a dragline excavator for a mining operation in New Mexico...

Jack Bolts McMaster - Know More

Choose from our selection of jack bolts, including steel square-head cup-point set screws, square-head extended-tip set screws, and more In stock and ready to ship...

jacking cradle mill installation and maintenance - Know More

16 x 22 Ball Mill Installation Manual Mill Installation Manual 16x22ft 2800kW Ball Mill Mills over 2743mm diameter 53 Third If maintenance jacking cradle assembly is available21....

Horizontal Hydraulic pole assembly installation - Know More

06-08-2012 0183 32 Horizontal Pole Assembly 34 each site should determine, document and train its personnel in safe work methods relevant to the site and to the pole assembly and installation 35 arrange the base section onto the packing and level so that the jacking lugs on either side of the section are horizontal and so that the underside...

No.416 Jianye Road, South Jinqiao Area,Pudong New Area, Shanghai, China.

Telephone : +86-21-58386189, 58386176

FAX : +86-21-58385681